Ender 3

Ender 3 DEFAULT

Ender 3 3D Printer

Creality Ender 3 News

Creality’s Ender 3 3D Printer is Now Fully Open Source
Creality3D, the Chinese manufacturer of 3D printers, has announced the open-sourcing of its most popular 3D printer, the Ender-3. This makes it the first Open Source Hardware Association certified 3D printer in China... Learn More

Ender 3' S FAQ:

Filament did not stick on the hotbed?
For newcomers, this is the most common problem. Do not worry, you can solve it easily. Generally,the distance between the nozzle and platform is too far or near. So rotary the knob under the platform to adjust the distance between the nozzle and platform again,at a piece of A4 paper distance or less).
Creality Ender 3 Bed Leveling – All You Need to Know
Any structure needs a strong foundation. The same is true for 3D-printed objects. Leveling the bed on your Creality Ender 3 will ensure that that all-important first layer is solid...

How to level Creality Creality Ender 3?
Move the nozzle so that it’s positioned over the left corner of the bed. A half-inch or so from both sides is a good location.
Slide the paper between the nozzle and the bed. If it doesn’t fit, drop the corner until it does.
Once the paper is able to slide under the nozzle, very slowly raise the corner with the adjuster. Remember: Clockwise moves the bed up. As you do this, gently slide the paper back and forth. The moment you feel even the slightest resistance to your moving the paper, stop turning the knob. That corner is (almost) ready to go.
Do the same for the other three corners of the build plate. Always advance the hot end to a new corner slowly. This will prevent damage to the build plate in case the nozzle starts to drag. If this occurs, simply lower the next corner (before starting the leveling process) to make some room.
After you’ve adjusted each corner once, go back and check the four corners again. You may have to do further adjustments to get all four correct.
Article: Creality Ender 3 Bed Leveling – All You Need to Know.

Sours: https://www.creality3dofficial.com/products/official-creality-ender-3-3d-printer

Facebook

Alan Mears, profile picture

I just noticed this when selecting Home-Z function. If I press Home Z multiple times one after the other, it… More moves differently each time. In this video, i pressed it four times with a second or so between. Why would the movement change when selecting the same function?

Nico Paulson, profile picture

How do you guys feel about leaving your printers running while your away from home

Steve Wesseler, profile picture

Has anyone printed their own urn yet?🤣

Rok Peršak, profile picture

HACKADAY.COM

Thingiverse Data Leaked — Check Your Passwords

Every week seems to bring another set of high-profile data leaks, and this time it’s the turn of a service that should be of concern to many in our community. A database backup from the popul…

Jason Chapman, profile picture

Hi Folks, I could use a little help with my Ender 3 Pro with BL-Touch installed. When I go to start a print, it… More auto levels and starts the nozzle cleaning strip. As it gets done with the first pass, it visits center quickly, then comes back. It leaves a small trail of filament behind. (see photo)
Edit: Video in Post
Only gcode adjustments I've made is adding the G29 to enable auto bed leveling. I've tried different SD cards too. Updated to Cura 4.11..
Any help would be appreciated to help it stop going to the center after the first pass. Ignore the "dirty" bed, its just glue.
Starting Gcode below:
___________________
;FLAVOR:Marlin
;TIME:4849
;Filament used: 3.83154m
;Layer height: 0.2… More

May be an image of text that says 'CREA'
Evaldas Karpačiauskas, profile picture

What could be a problem for this flex on the print corners? It always happening with every print, even tried to… More reducing bed temperature to 50 degrees, but still the same issue.

Using Ender 3 V2 with PLA that was included in the set.
200 degrees on the nozzle, 60 degrees on the bed.

No photo description available.
Andrew Shaner, profile picture

Freakin BS, printed on my Ender Extender 400Xl, 1 day and 2 hours of printing a base for a bust im printing, n the print falls apart. Anyway how to fix this problem?

No photo description available.
Cassen Burnett, profile picture

What do people use for filling gaps on big builds you do?

Branden Morris, profile picture

Can anyone here shed a little insight on the use of octopi and a camera? I have a Pi4 and an Arducam Motorized Focus. I am slightly new to the whole Pi world and Octopi works great for me, but I would love to put this printer in my basement and still be able to watch it from upstairs. the LED Light on the camera does not illuminate. The ribbon… More cable is connected correctly. I am not too sure what else to do. I SSH'd into the pi to look at the config settings and enable the camera. vcgencmd get_camera shows supported = 1 detected = 0.
Any clues?

Jeff Goldsack, profile picture

Ok group you can see in the picture I have some pretty serious z-banding going on. The print is not losing any z… More height, and for the items I am printing, I really don’t care, but this is clearly an issue that must be resolved.

I am running dual z setup on my E3V2, with direct drive. Both motors are connected together off the same cable. I am using flexible couplers for the z rods. Z-rods are straight, and I have cleaned and lubed them a few days ago to see if that was the issues (it clearly wasn’t). I have tightened my motors to the frame so they are not vibrating. And yes, bed is level, and my x-gantry is also level.

The banding is happening from the bottom upwards, and clearly gets worse as it gets higher.

Thoughts on what could be causing this issue, and how I might fix it?

No photo description available.
Blade Nicolini, profile picture

Y'all idk what to do. Swapped out my white hatchbox with a brand new grey hatch box now it's not extruding properly. Looked like it was a clog so I bought and replaced the nozzle and cleaned out all the crap in the tube etc. It's still not extruding...Y'all idk what to do. Swapped out my white hatchbox with a brand new grey hatch box now it's not extruding properly. Looked like it was a clog so I bought and replaced the nozzle and cleaned out all the crap in the tube etc. It's still not extruding...See More

Ricky Wuorinen, profile picture

Is it possible to print a working drone?Is it possible to print a working drone?

Sours: https://m.facebook.com/groups/1275880512515568
  1. Message nintendo
  2. Browning 7mm mag rifle
  3. Yamaha dealer appleton

Retailing for a very-reasonable $240, the Creality Ender 3 Pro is one of the most popular filament-based 3D printers, attracting both beginners and budget-focused makers. The device ships unassembled and uses an open-source design that makes it easy to modify. However, the great support and solid output quality of this printer also make it easy-to-use. Whether you’re interested in buying your very first 3D printer or you’re looking to set up a fleet for manufacturing, the Creality Ender 3 Pro is one of the best 3D printers you can buy.

Specifications

Machine Footprint17.5 x 17 x 18 inches (44.5cm x 43.2cm x 45.7cm)
Build Volume8.7 x 8.7 x 9.8 inches (220mm x 220mm x 250mm)
Material1.75mm PLA, ABS, PETG
Nozzle.4mm
Build PlatformRemovable Flexible Textured Sheet
ConnectivitymicroSD, USB
Interface3.25" LCD w/ Dial Button

Creality Ender 3 Pro: Included in the Box

The Creality Ender 3 Pro ships unassembled and includes all of the tools you need to put it together and get it running. In addition to all of the printer components, the box includes: a full set of Allen keys, zip ties, a set of flush cut wire snips for cutting filament, a scraper for removing parts from the bed, a microSD card, a microSD-to-USB reader, a small sample coil of PLA filament, and a few extra parts for the assembly process. All of the bolts are bagged in sets which are labeled with their measurements, which is very helpful during the assembly process.

Assembling the Creality Ender 3 Pro

Although the Creality Ender 3 Pro is a DIY kit 3D printer, the overall assembly process is designed to be friendly to users of all skill levels and can be comfortably completed in an afternoon. There is no soldering, crimping, or other advanced techniques required that would put this kit out of reach for a beginner with limited tools and/or experience. Building the Ender 3 Pro took me just over an hour from unboxing to flipping the power switch, and I didn’t need a single tool that wasn’t included with the printer.

The assembly guide breaks down the assembly into 12 steps that are easily completed sequentially and is also included as a digital .pdf on the microSD card. Creality also includes a video showing the assembly process on the microSD card if you prefer a video guide instead of a written one. Among various quality-of-life improvements over the original Ender 3, the Ender 3 Pro has built-in belt tensioners for the X and Y axes that allow you to manually adjust tension if the belt isn’t stretched properly.

Loading Filament and Leveling on the Creality Ender 3 Pro

Loading the filament is a breeze. I was able to easily load filament through the injection molded extruder and into the white Bowden tube. The 350 Watt Meanwell-brand power supply heated both the nozzle and the bed to loading temperature in just under two minutes, which meant I wasn’t waiting around for the bed to reach printing temperature after the nozzle had already heated.

Once I had loaded filament into the extruder, I leveled the bed by using the included triangular piece of paper and adjusting the nozzle height with the thumbscrews at all four corners of the bed. This process is relatively straight-forward and I didn’t run into any problems during leveling. If you level the bed carefully, you'll get prints that adhere well to the build platform without being deformed. The piece of paper should be lightly pressed down into the build platform; too close and the paper becomes pinned down, too far and it can move freely. This can be difficult on a flat glass bed if the glass isn’t perfectly flat, but the combination of aluminum bed and textured sheet was easy for me to level quickly and accurately.

Creality Ender 3 Pro Build Quality

The Creality Ender 3 Pro ships with the V4.2.2 controller board, which is the standard board for this model of printer. The wiring job is professional, with several of the wiring connectors affixed with a silicone potting compound into their sockets to prevent them from coming loose during shipping or operation.

The wires are bundled and the overall cable management is clean and allows for good airflow over the stepper drivers. The board accepts a microSD card for uploading .gcode instructions and can also be controlled via the USB port on the front of the machine.

The Ender 3 Pro's V4.2.2 controller board features HR4988 stepper drivers, which can create a noticeable amount of noise during printing. Combined with the noisy fan that cools the controller board and the intermittent fan on the power supply, this printer makes a surprising amount of noise when printing. The buzzing from the stepper motors reminded me of my very first 3D printer from 2013, a Printrbot Jr. that could be heard from clear across the house through multiple walls when it was printing.

If you’re planning to use this printer near your desk, it may be distracting during fast travel movements and when the power supply fan kicks on. I found that I was unable to concentrate with the machine on my desk, and had to move it to the other side of the room while it was running.

Printing on the Creality Ender 3 Pro

The Ender 3 Pro ships with a microSD card that contains a user manual, a troubleshooting guide, various USB drivers, and several pre-sliced models in .gcode format. These pre-sliced models can be printed by simply inserting the microSD card into the printer and selecting a model.

I ran my first test print using the “cat-3.5H.gcode” file and, while it was printing, I took a look at the .gcode file in a text editor. The file was sliced at a .1mm layer height, using 3 perimeters, and prints completely hollow with 12 solid layers on the bottom and top of the model. This is an unusual strategy for printing small models, as having an internal infill structure can help to support any material overhangs that occur on the inside of the model.

Despite the unusual printing configuration of this test file, the printed model featured a good amount of surface detail with no major visible defects aside from some stringing that occurred while printing the ears. To remove the print, I peeled the flexible magnetic build plate off and bent slightly, allowing the print to pop right off. The raft separated easily from the model and didn’t leave any defects on the bottom surface. The test part is an impressive example of what the Creality Ender 3 Pro is capable of.

Software and Settings

Creality ships the Ender 3 Pro with their own slicer called ‘Creality Slicer’, which is compatible with Windows PCs and is based on the open-source software Cura.. Other common slicers for this open-source printer include Cura, PrusaSlicer, and Simplify3D.

A typical printer in this price range, such as the Mingda D2 ($235 on Amazon), will ship with a copy of Cura and a printer profile that was designed for that specific machine. These profiles can be hit or miss and typically require a lot of dialing in to get a good result.

For this review, I used both Creality Slicer as well as PrusaSlicer to print a model and used the default settings at .2mm layer height for both to directly compare them.The model I used is the Benchy, a common benchmarking test used for this style of 3D printer that offers an insight into the performance of the printer when making difficult-to-produce geometry.

Creality Slicer Settings on the Ender 3 Pro

ProfileFast (0.2mm)
MaterialCommon PLA
Platform AdhesionNone

I used the default ‘Fast’ profile for the Ender 3 Pro built into Creality Slicer to test out the printer and see how much detail it was able to produce. The model printed with no major visible defects, save for the infamous ‘hull line’ which typically occurs when the printer transitions from sparsely filled layers to solid layers.

The layers laminated evenly, and I only saw a few visible bumps caused by the start and stop point of each toolpath on the outermost contour. For a part printed with no changes to the software, I was satisfied with the overall quality of the Benchy.

PrusaSlicer Settings on the Ender 3 Pro

Layer Height0.2 mm
Infill Percentage20%
Print Speed40mm/second
Extruder Temperature205 degrees Celsius (401 degrees Fahrenheit)
Heated Bed Temp60 degrees Celsius (140 degrees Fahrenheit)

I ran the same test print using PrusaSlicer, another common slicer program that also includes a native printer profile for the Ender 3 Pro. In addition to the hull line artifact, this print also showed some banding towards the top of the print and seemed to lack a bit of the detail present in the model sliced with Creality Slicer.

This print wasn’t quite where I would like to see a benchmark print, and some optimization of the software (print speed, retraction settings, etc.) would likely be required to get this part to an acceptable level of quality. I’ve printed this part using similar settings on the Prusa MK3S using the same material in the past, and the quality is much higher than what I saw here. While the Prusa MK3S is a more expensive machine, I was still surprised to see this much of a difference in a test part using the same software.

Printing a second test print on the Creality Ender 3 Pro

I was curious about the amount of banding present in the model printed with PrusaSlicer, so I decided to re-run another one of the pre-prepared files from the SD card to confirm the problem wasn’t being caused by a hardware issue. I ran the piggy bank test part, and it came out without any of the visible banding that I noticed on the model sliced with PrusaSlicer. The vertical walls were smooth and even, and the model seemed to be clear of any major defects.

The PrusaSlicer profile, while a good starting point for this printer, clearly requires a bit of calibration to get the best results. I’ve found that reducing print speed is typically a quick way to troubleshoot and can have a major impact on the overall quality of the part, and that may be a setting worth experimenting with to get the best results.

Adjusting retraction is another important consideration, as the Ender 3 uses a Bowden extruder, which pushes the filament through a long tube before it gets to the hot end. This pushing (and pulling during retraction) can cause defects in the print if not properly calibrated, so this might be worth investigating as well.

Bottom Line

By including Creality Slicer with the Ender 3 Pro, Creality has simplified the printer experience for first-time users who are interested in getting their printer up and running without spending a lot of time experimenting with third party software. I was impressed with how easy the Creality Slicer software was to install and use with the Ender 3 Pro, because most other manufacturers with printers in this price range ship without first-party software. The basic settings to create a print are brought to the front of the app and the included “expert” mode will let you adjust settings as you become more comfortable with the printer.

Whether you are a beginner interested in building your very first printer or an experienced entrepreneur looking to create a print farm to produce 3D printed products, the Creality Ender 3 has a lot to offer with only a few notable drawbacks. The noise produced by the Ender 3 Pro while printing is definitely a downer for anyone living in a studio apartment, and the lack of an enclosure to retain heat should be considered by anyone interested in printing with a higher-temperature material like ABS or Polycarbonate. Creality also offers the Ender 3 Pro V2 ($279 on Amazon), which features silent stepper drivers and a more modern interface at a slightly higher cost.

Other printers in this price range, such as the Anet ET4X ($199 on Amazon), offer similar features and specifications, but the removable textured build platform and the fast-heating 350W power supply on the Ender 3 Pro make it an easy choice for anyone looking for a user-friendly machine. In addition, the open-source Ender 3 Pro has a large and robust user base and multiple online communities dedicated to modifying and experimenting with their Creality machines.

It’s clear that Ender 3 Pro has a lot to offer anyone who is interested in 3D printing. It’s an excellent first printer for a beginner or an additional machine for the experienced hobbyist.

Sours: https://www.tomshardware.com/reviews/creality-ender-3-pro-3d-printer
Automate Your Ender 3!

Creality3D Ender 3 3D Printer Kit

Easy Assembly

The Ender 3 comes with easy-to-follow instructions and user-friendly parts that can be assembled by anyone. With aluminum framing and stainless steel screws, the Ender 3 is made to last once it's put together.

Hackable and Upgradable

The Creality 3D printer line is completely open-source, allowing for add-ons and upgrades of almost every component on the machine. From a BL Touch automatic bed leveling probe, to a Micro-Swiss or E3D all-metal hotend, to a Bondtech extruder - the Creality 3D printers give you an awesome foundation for experimentation.

Tech Specs:

  • Print area: 220mm x 220mm x 250mm
  • Nozzle: Brass 1.75mm x 0.4mm
    • can be swapped out for 0.3mm or 0.2mm
  • Max. nozzle temp: 260°C
  • Power input: 24V / 270W
  • Printer weight: 7.5kg
  • Printer size: 420mm x 410mm x 470mm

What's in the Box

  • Extra nozzle
  • Spatula
  • Hex key
  • Pair of wire cutters
  • Nozzle cleaner
  • Coil of filament
Why buy from MatterHackers?

Put simply, MatterHackers is the smart place to shop for all things 3D printing and digital manufacturing. The MatterHackers pros are here to partner with you through every step of your journey turning idea into reality and here are just a few of the perks you’ll receive as a customer:

  • Free, Fast Shipping on orders over $35
    No matter how large or small your order is, U.S. customers will always receive free, fast shipping on orders over $35. Most orders placed before 4pm ET M-F ship same day.
  • Lowest Price Guarantee
    We work hard to make sure that we offer the lowest prices available - shop confidently knowing you’re getting the best deals on the items you love. Learn more about our Lowest Price Guarantee here.
  • Rewards Program
    We just want to help you save - MatterHackers' customers can earn a store credit of 3% back on all eligible purchases. Learn more and become a Rewards Program member here.
  • Success Guarantee
    MatterHackers is invested in your success. From our free phone and email support to our easy exchange program, MatterHackers sets you up on the road to success even with just one purchase. Learn more here.

Have a question about this MatterHackers Creality3D Ender 3 3D Printer Kit? Looking for a recommendation? No problem. Feel free to contact us.

Sours: https://www.matterhackers.com/store/l/creality3d-ender-3-3d-printer-kit/sk/M34AK4ZG

3 ender

.

My Ender 3 Journey 2.5 Years Later! Still Worth Getting?

.

You will also be interested:

.



376 377 378 379 380